VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor

If your VVDI2 have BMW OBD Function, then you can open this function

UKOBD2 Provide top quality VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor, if you need VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor, or have any questions about VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor, welcome to contact us.

Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Porsche Piwis III, USB Link 2, Scania VCI3, CAN Clip, wiTech MicroPod 2, T300 key programmer, locksmith tools

images of VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor


VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor

Note: VVDI2 now add BMW FEM & BDC functions, VVDI2 Must have BMW OBD Function(SV86-3), then can open this function.

There are two ways to get this function:


1.If you only have VVDI2 with BMW OBD Function, then you can buy this authorization.

2.If you have VVDI2 with BMW OBD Function, and Ikeycutter Condor, then you only need to pay 600USD to get this authorization(SV86-S).



3.If you want other BMW FEM BDC Key Programmer, you can choose YH BMW FEM (SK226) on our site.

VVDI2 - BMW FEM/BDC system(function released and available, just no user manual)
Users can refer to following information (3 steps for make keys: get key info->programming FEM/BDC system->make keys)

1.support make new key with ignition switch(support add spare key and all key lost, all key lost require ISN)
2.support reset FEM/BDC KM(cluster require reset manually)
3.support erase key(after erase the key position become blank position)
4.support backup coding
5.support restore coding

Notes:
1.backup coding and restore coding can direct operation generally.
2.add keys, reset KM, erase key must programming FEM/BDC system first
3.in FEM/BDC interface, if 'get key info' the type not support, it will show: customer should use "BMW E-sys software" program FEM/BDC system. then programming FEM/BDC system with VVDI2-BMW
4.when operation on 'programming FEM/BDC system'interface, please don't close this software window until all procedures completed.
5.programming FEM/BDC system, require soldering and get eeprom.(FEM 95128 chip, BDC 95256 chip)usually there are 2 same chips on the module, please refer to the software diagram, select the correct one.
6.programming FEM/BDC system, must restore the original eeprom, restore coding. if cannot restore coding or after restore coding assemble FEM/BDC module back to car, but with problem(such as the remote control cannot start the car
or the car with window problem)please use "BMW E-sys software" coding for FEM/BDC system
7.if connect power to FEM/BDC module, but the relay keep ringing, please contact technical support for help. usually operation on FEM/BDC should be ok, just need to programming.



Go to Buy: VVDI2 BMW FEM & BDC Functions Authorization Service Without Ikeycutter Condor

Tags: vvdi2 bmw authorization, vvdi2 fem , vvdi2 bdc , vvdi2 authorization
Prev: One Year Update Service for XTOOL X100 PAD
Next: CAS Plug for VVDI2 BMW or Full Version (Add Making Key For BMW EWS)